Furnace & heating
AC repair
Heat pumps
Carrier
TraneSeasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Get your free estimateLennox Heat Pump Installation in Miami: What to Know First
Lennox heat pump installation in Miami typically runs $4,130 to $8,850 depending on the series, home size, and whether ductwork needs modification. We’re an independent Lennox service provider, not a factory-authorized dealer, which means we install and service these systems without the overhead that drives up quotes at brand-exclusive shops. Most installations take one to two days once equipment is on-site, and we hand you a written price before any work begins.
This page is for Miami homeowners who own a Lennox heat pump, are considering one, or inherited one with a house they bought. If your Lennox is acting up or you’re planning a replacement, call (850) 754-6042. Marco Benitez and our crew will tell you straight what’s involved and what it costs. No pressure, no mystery pricing.
Key Takeaways:
- Independent Lennox heat pump installation, not factory-authorized, which keeps pricing straightforward
- Written price before work starts, every job, no exceptions
- 365-Day Done Right Promise on every installation
- Factory-trained techs who work on Lennox, Carrier, Trane, and six other major brands
How Lennox Products Fail – and How We Fix Them
Lennox builds a solid heat pump, but every brand has its patterns. Here’s what we see repeatedly in Miami homes:
- Defrost control board failures on Merit series (ML14XP, ML17XP): Miami’s humidity means the outdoor coil frosts up more often during the few cool nights we get. The defrost board cycles more frequently, and on Merit units it’s a known weak point. When the board goes, the coil ices over and the system either stops heating or blows cold air. We replace the board, verify the defrost cycle timing, and confirm the sensor is reading correctly before we leave.
- Reversing valve sticking on Elite series (XP20, XP25): The reversing valve is what switches the heat pump between cooling and heating mode. Elite units run high compression ratios, and over time the valve can stick mid-travel. You’ll hear a chattering sound near the outdoor unit and the system won’t switch modes. We diagnose it with pressure readings rather than guessing, and replace the valve with an OEM Lennox part when needed, not a generic substitute that voids your compressor warranty.
- Outdoor coil corrosion on any Lennox unit within three miles of the coast: Salt air eats aluminum fins faster than anything. Lennox coils are built thin to hit efficiency numbers, which makes them more vulnerable in Miami Beach, Key Biscayne, and coastal Coral Gables. We coat new coils with a corrosion inhibitor on every coastal installation. It’s a $200 – $400 add-on that adds years to coil life. Most shops skip it. We don’t.
- ECM blower motor failures on Dave Lennox Signature Collection (XP21, XP25, SL25XPV): The variable-speed blower motor is a $900 – $1,400 part. It fails most often because of voltage spikes or clogged filters forcing the motor to work against high static pressure. Miami’s humidity means filters load up fast. We check static pressure on every call, plain and simple. When we install a Signature unit, we size the ductwork properly or we tell you upfront that the current ducts won’t let the system hit its claimed efficiency.
- Refrigerant leaks at the A-coil on XP and MLA series units installed before 2018: Lennox used aluminum evaporator coils that were prone to pinhole leaks, especially in humid environments. Miami accelerates the corrosion. If your system loses charge every season, it’s likely the coil. We pressure-test with nitrogen, find the exact leak point, and give you a written price for coil replacement versus a new system. No vague hand-waving.
Styles & brands we work with
Our Lennox Heat Pump Installation Process
Here’s how a Lennox heat pump installation goes with us, step by step:
- 1
Call and talk to a person: You call (850) 754-6042 and a live person answers. We schedule a time inside a two-hour window and tell you the tech’s name before they arrive.
- 2
Load calculation and duct check: We measure your home, check existing ductwork, and look at your electrical panel. If your old system was oversized, which happens constantly in Miami, we’ll tell you and size the new Lennox correctly. Oversized equipment short cycles, which kills compressors and spikes humidity indoors.
- 3
Written quote, no surprises: Marco or your tech writes the price down before anything gets ordered. That price includes equipment, labor, refrigerant, electrical work, pad, and haul-away. You sign it. You know the number. No “discovery fees” later.
- 4
Install day: We pull the old unit, set the new one on a level pad, braze the line set with nitrogen flowing through it to prevent oxidation inside the lines (that’s the stuff that clogs TXVs later), pull a proper vacuum, and charge the system by subcooling and superheat readings, not guesswork.
- 5
Test and verify: We run the system in both cooling and heating modes, check airflow, check the defrost cycle, and take static pressure readings. If your ducts are undersized, you’ll know before we leave because we measured it.
- 6
Cleanup and the guarantee: We leave the site clean – no refrigerant caps on the ground, no copper shavings in the grass. Every installation comes with the 365-Day Done Right Promise. If something isn’t right within a year, we come back and make it right. That’s not a pitch; it’s how we’ve operated since 2003 under The Garrison Standard.
What Lennox Heat Pump Installation Costs in Miami
Honest numbers, because that’s what you came for:
| Scenario | Typical Range |
|---|---|
| Lennox Merit series (ML14XP/ML17XP) 3-ton heat pump, straightforward swap with existing ductwork | $4,130 – $5,600 |
| Lennox Elite series (XP20/XP25) 4-ton heat pump, high-efficiency install | $6,200 – $7,800 |
| Dave Lennox Signature Collection (SL25XPV) 5-ton variable-speed with duct modifications | $7,900 – $8,850 |
What moves the price: ductwork condition, electrical panel upgrades, line set replacement, coastal corrosion coating, and whether you’re going from a straight AC to a heat pump (which requires new thermostat wiring and often a new air handler). Every estimate is free, in writing, and good for 30 days. Call (850) 754-6042 and Marco will get you an exact number.
See the difference
Before
After
Before
After
Before
AfterWhy Miami Homeowners Call Dalton Heating & Air Miami for Lennox Work
We’ve been running calls in Miami since 2003 as part of Garrison Partners, and the reason people stick with us is simple: we write the price down before we touch anything, and we stand behind the work for a full year. That’s The Garrison Code. Every tech who shows up at your door is background-checked, uniformed, and factory-trained on Lennox equipment. Not a trainee learning on your dime.
We carry the full range of Lennox parts in our trucks – defrost boards, reversing valves, TXVs, ECM motors – because hunting down parts from a supply house wastes your afternoon. And if your Lennox is truly dead and it’s time to consider replacement, we’re also factory-trained on Carrier and Trane, so you get an honest comparison, not a sales pitch for whatever brand we happen to stock. That’s the difference between working with a company that fixes what’s broken and one that’s angling for a commission check. Tell me what it’s doing, I’ll tell you what it costs – in writing, before I touch it.
FAQs
No. As an independent Lennox service provider, we install and service Lennox equipment using OEM parts when required, and our work does not void your manufacturer warranty. What voids a Lennox warranty is improper installation – oversized equipment, bad refrigerant practice, skipped vacuum procedures, mismatched coils. That’s exactly the kind of work we document and verify on every job, so your warranty stays intact. Call (850) 754-6042 and ask us about your specific model.
Most Lennox heat pump installations take one full day when ductwork is in good shape, and two days if we’re modifying ducts or replacing the air handler. We’ll give you a firm timeline when we write the quote, and we arrive inside the stated window. If something changes on install day, we tell you before we start, not after.
Replace it when the repair cost exceeds 40% of the system’s remaining value, or when the compressor or coil has failed and the unit is past 10 years old. In Miami’s climate, a 12-year-old Lennox that’s been through 12 humid summers and salt air is living on borrowed time. We’ll give you a straight answer with numbers behind it, not a scare tactic. Free estimates at (850) 754-6042.
Some are. Defrost boards for older Merit units and certain Signature Collection variable-speed motors can take 3 – 7 days from Lennox’s regional warehouse. Most common parts – capacitors, contactors, pressure switches, TXVs, defrost sensors – we stock on the truck. If your part needs ordering, we tell you on the spot and keep you updated. No “we’ll call you back” and then silence.
Yes. A dual-fuel setup – Lennox heat pump paired with a gas furnace – works well in Miami’s cooler winter nights and still gives you efficient cooling the rest of the year. We’ll evaluate your existing furnace, thermostat wiring, and electrical panel, then give you a written price for the full package. This is a specialized install, so we make sure the control wiring and staging is set up correctly the first time.
Ready to Move Forward?
If your Lennox heat pump needs replacing or you’re planning an installation, call (850) 754-6042 now. A live person answers, we schedule inside a two-hour window, and your quote is free and in writing. That’s how we’ve done it in Miami since 2003, and that’s how we’ll do it for you.
Written by Marco Benitez, Owner, Dalton Heating & Air Miami at Dalton Heating & Air Miami, serving Miami and nearby areas.